*mymedicalexpo

Catalogs
Zirkonzahn
Fresco Ceramics Application

Fresco Ceramics Application

Product catalog summary

Overview: The document provides detailed specifications and procedures for using Fresco Ceramics, specifically focusing on monolithic and slightly reduced zirconia structures. It highlights the application of various Fresco Enamel products to enhance the aesthetic qualities of dental restorations.

Specifications:

Fresco Enamel Opal: Provides opalescent effects, increasing brightness by one shade with a layer thickness of 0.3 – 0.7 mm.
Fresco Enamel Transpa 3: Whitish luminous ceramic paste that enhances brightness and opacity.
Fresco Enamel Fluo: Creates a natural, slightly translucent effect.
Fresco Enamel Transpa Grey: Lowers brightness for a more subdued appearance.
Fresco Enamel Transpa Neutral: Recreates natural tooth translucency and color.
Fresco Enamel Transpa Orange: Adds an orange-like effect for characterisation.

Procedures:

Fresco Firing: Detailed firing workflows for monolithic and slightly reduced crowns and bridges, including temperature settings, heating rates, and vacuum conditions.
Glaze and Stain Firing: Optional procedure to enhance the surface finish, with specific temperature and timing guidelines.

Recommendations:

Perform Fresco Firing n. 2 to maintain the modeled surface.
Optional polishing and characterisation can be done without structural loss.

Key Parameters:

Temperature settings range from 780°C to 810°C depending on the firing stage.
Heating rates vary between 20 – 45°C.
Vacuum conditions are specified for certain firing stages to ensure optimal results.

Product Codes: Each Fresco Enamel and Gingiva product is associated with a specific code for identification and ordering purposes.

Conclusion: The document provides comprehensive guidelines for achieving high-quality dental restorations using Fresco Ceramics, emphasizing the importance of precise application and firing techniques to achieve desired aesthetic outcomes.

Catalog excerpts

Monolithic zirconia structure Slightly reduced zirconia structure FRESCO CERAMICS APPLICATION

Open the catalog to page 1

TEST STRUCTURE: Minimal Cutback 0.3 – 0.7 mm FRESCO ENAMEL LUMINESCENCE VALUE OVERVIEW FRESCO ENAMEL FLUO/CONTROL UV LAMP KEAD4501 Fresco Enamel Fluo is used to recreate the natural restoration with a slightly translucent and luminous effect. In order to create different degrees of FRESCO ENAMEL TRANSPA 3 KEAD2301 Fresco Enamel Transpa 3 is a whitish luminous ceramic paste which increases the brightness and opacity of the zirconia structure. other Fresco pastes. FRESCO ENAMEL OPAL KEAD4601 Fresco Enamel Opal provides the restoration with a beautiful opalescent effect and recreates a natural luminous...

Open the catalog to page 2

NOTE: for monolithic structures. FRESCO FIRING WORKFLOW FOR LAYERING MONOLITHIC SINGLE CROWNS AND SMALL BRIDGES SINTERED – MONOLITHIC CHARACHTERISED WITH ICE STAINS 3D BY ENRICO STEGER FRESCO ENAMEL FLUO/ CONTROL UNDER UV LAMP FINAL RESULT TIP: Perform a Fresco Firing n. 2 to maintain the modelled surface Fresco Firing n. 2. GLAZE AND STAIN FIRING OPTIONAL: GLAZE AND STAIN FIRING Heating rate Heating rate Heating rate Vacuum start Vacuum start Vacuum start OPTIONAL TIP: the surface can be further characterised or polished and/or can be carried out without loss in structure. TEXTURE OF A MONOLITHIC...

Open the catalog to page 3

FRESCO FIRING WORKFLOW FOR LAYERING SLIGHTLY REDUCED SINGLE CROWNS AND SMALL BRIDGES SINTERED – SLIGHTLY REDUCED FRESCO ENAMEL FLUO/ CONTROL UNDER UV LAMP CHARACHTERISED WITH ICE STAINS 3D BY ENRICO STEGER APPLICATION OF FRESCO ENAMEL FINAL RESULT ICE Stains 3D by Enrico Steger FRESCO FIRING n. 1 GLAZE AND STAIN FIRING OPTIONAL: GLAZE AND STAIN FIRING Heating rate Heating rate Heating rate Heating rate Vacuum start Vacuum start Vacuum start Vacuum start

Open the catalog to page 4

FRESCO FIRING WORKFLOW FOR LAYERING MONOLITHIC OR SLIGHTLY REDUCED PRETTAU® BRIDGES SINTERED – MONOLITHIC BEFORE FRESCO FIRING n. 1 AFTER FRESCO FIRING n. 1 CHARACHTERISED WITH ICE STAINS 3D BY ENRICO STEGER BEFORE FRESCO FIRING n. 2 GLAZE AND STAIN FIRING AFTER FRESCO FIRING n. 2 AFTER FRESCO FIRING n. 2 AFTER OPTIONAL GLAZE AND STAIN FIRING OPTIONAL: GLAZE AND STAIN FIRING Heating rate Heating rate Heating rate Heating rate Vacuum start Vacuum start Vacuum start Vacuum start Long-term cooling Long-term cooling Long-term cooling

Open the catalog to page 5

FRESCO GINGIVA VS. NATURAL GINGIVA FRESCO GINGIVA 1 KEAD6301

Open the catalog to page 6

All Zirkonzahn catalogs and technical brochures

Archived catalogs

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list